Accessories

Whether you like to prepare your stabilizers because you're waiting for your keyboards to arrive or prefer to tune them before placing them on the PCB, this Stabilizer Tester is perfect to test and tune your stabilizers before installing them onto your keyboard. 

The Stabilizer Testers are made with FR4, the same material as your PCB, which makes them a great substitute to test your stabilizers on.

Specs:

• 138mm x 70mm
• Supports 6 * 2U, 1 * 6.25U and 1 * 7u stabilizers
• Includes 4 Rubber bump-ons

Material: Low Elasticity STS Wire

• Material Thickness: 1.65mm
• Straightness: ±0.1mm (Refer to Notes)
• Manufactured in South Korea

Features:

• Low Resonance: Made from domestically produced low elasticity stainless steel wire, characterized by low resonance and a bright finish that allows for even application of lubricants.
• Minimal Deformation: Produced with wire balance equipment, ensuring an error margin within ±0.1mm.
• Smooth Surface: Features chamfering (beveling) and precise barrel polishing for a uniform surface.
• Recommended Usage: Suitable for use with Cherry, Gateron, WS, and Designer stabilizers.

Notes:

• Tolerance: While produced within specified tolerances, the nature of thin steel wire may result in variations beyond the stated tolerance, which is not grounds for exchange or return.

3M Keyboard Bumpons are sold in packs of 4.

Replacement silicone bumpons/feet used on the majority of keyboards.
3M SJ5302 Bumpon - 5⁄ 16 x 1⁄ 12", Clear

• Apply sticker bumpon onto your keyboard into designated spot(s)
  

Protect your keyboard with this carrying case by TX Keyboards. Available in Grey colourway.

Specifications

• Small fits a 60%, 65%, and 66% boards
• Medium fits a TKL
• Large fits a full size board

Outer Dimension

• Small - 38 x 19.5 x 10cm (LxWxH)
• Medium - 42 x 21 x 10cm (LxWxH)
• Large - 50 x 24 x 9.5cm (LxWxH)

Inner Dimension

• Small - 32.5 x 12 x 5cm (LxWxD)
• Medium - 36.5 x 14.7 x 5cm (LxWxD)
• Large - 44.5 x 17 x 5cm (LxWxD)

Geon Plate Support Fork is utilized to support and plate and PCB during switch installation.

Geon Plate Support Fork Features:

• Process: Injection Mold
  
• Material: POM
• Dimension: 104 x 78 x 3.4mm
• Four prong on one end and a single prong on the opposing end

Includes:

• 1 Geon Plate Support Fork

Stabilizer set includes five pairs of stabilizers, two size 6.25U, one 7U and eight 2U wires. 6.25U wires come in 100mm and 100.2mm, 2U wires are 24mm and 23.8mm to provide the best fit for your keyboard.

Silver-plated PCB mount stabilizers made by Gateron.

• Black/Yellow or White coloured housing
• Nylon Base
• POM Stem
• Silver-plated Steel Wire
• Silver-plated Screws
• Includes rubber washers
  

* We recommend that you lubricate the stabilizers with Krytox 205g0 or Krytox XHT-BDZ  prior to use.

Please note: this item is final sale. No returns or refunds will be accepted.

Stabilizer set includes one size 6.25U (WK), 7U (WKL) and four 2U pieces.

The newest "ALMOST PERFECT" TX Stabilizers!

Implementing a patented technology, kin25 of TX Keyboard has improved the design of screw-in stabilizers to minimize rattling and prevent wire pop-out (using stab stoppers included with the set). The patented design features a double shot stabilizer stem with a POM outside and TPU & POM mixture inside. This mixture helps to minimize wire rattle and bottom out noise.

* We recommend that you lubricate the stabilizers with a thin coat of Krytox 205g0 or Krytox XHT-BDZ prior to use.

Specifications

PCB mount, screw in, compatible up to ANSI TKL

One WK/WKL kit includes:

• 10x stabs
• 4x short wires 2U
• 2x long wires (1x 6.25U and 1x 7U)
  
• 1 set of screws
  

Springs are sold in packs of 110.

The TX Magnetic Springs are recognized for their strict adherence to quality control standards, ensuring the production of uniform and top-notch springs for switches. The TX Magnetic Springs—designed exclusively for magnetic switches and not compatible with MX-style mechanical switches.

TX Magnetic Springs comes with 2 different sizes:

Medium – 18mm: Offers a balanced, responsive press with a clean return.
Long – 20mm: More progressive force per each press with faster return.

Specs:

• Cherry MX HE compatible
• Springs have been QC'd to have less than +/- 1 deviation
• Lengths:
  
• Medium (15mm), Long (16mm)
  
• Bottom Out Force
• 45g, 50g, 55g, 60g, 65g, 70g
• Pack of 110

* We recommend that you lubricate the springs with Krytox 105 or Krytox 106 prior to use.

Please note: this item is final sale. No returns or refunds will be accepted.

Geon Trimmer – Switch Stem & Keycap Calibration Tool

The Geon Trimmer is a precision tool designed to calibrate switch stems and keycaps for optimal fit. If a switch stem is too thick to accommodate a keycap properly, the trimmer can be used to adjust the stem for a better fit.

Features

• Material: STS316L Stainless Steel
• Finish: Raw
• Size: 100 x 16 mm (3.94 x 0.63 in)

Usage Guide

Switch & Stabilizer (“+” Stem) Calibration

• The trimmer can be used in any orientation regardless of the switch's direction.
• Rather than cutting, it works by gradually reshaping the stem through repeated use.
• Use the tool multiple times for switches or keycaps that require fine adjustment.
• Apply the trimmer both vertically and horizontally along the stem.
• Handle with care: this is a precision-tolerance tool that is sensitive to impact.

Keycap Calibration

• Keep the keycap level during calibration.
• Do not use the trimmer vertically for keycaps.
• If the switch is rotated 90 degrees, use the trimmer vertically.
• Remove excess material (burrs) by carefully trimming the stem.
• For stem calibration, always use the tool in a vertical motion.
• As a precision tool, avoid dropping or applying excessive force.

Stabilizer set includes one size 6.25U (WK), 7U (WKL) and four 2U pieces.

SSS - Fourwraps V2 Stabilizers

Designed by Morning Workshop and made in Korea, the Fourwraps V2 Stabilizers are built for smooth stock performance with minimal tuning required. Tight tolerances and an internal wire guide help reduce wire ticking and balancing needs, making these a true lube optional stabilizer.

Key Features

• Designed by Morning Workshop
• PCB Mount
• Lube Optional
  
  • Lubing is recommended for fine tuning but using the stabilizer stock is acceptable
• Bi-directional Stem
• Stem Internal Wire Guide: Reduces wire ticking and minimizes wire balancing requirements
• Supports Clip-in & Screw-in
  
  • Screw-in requires removal (clipping) of the clip-in feet (front and back)
    
    • There are two sized washers provided. It is recommended to use the bigger washer combined with a small washer for the bigger opening and a single small washer for the clip-in (smaller) opening
  • Screw-in on the front and back mounting points help to minimize wire balancing requirements
• Made in Korea
  

What’s Included

• 10 Housings
• 10 stems
• 4 2U Wires
• 1 6.25U Wire
• 1 7U Wire
• Set of Screws & Washers

Please note: this item is final sale. No returns or refunds will be accepted.

Geon Tweak Board is a precision tool used to determine the flatness of stabilizer wires and allows for more precise adjustments.

Geon Tweak Board Features:

• Material (Aluminum): 
  • Surface Treatment: Sand Blasted, Silver Anodization
    
  • Weight: 141g
    
• Parallelism: 0.05mm
• Size: 150mm x 50mm x 8mm

Includes:

• 1 Geon Tweak Board
  
• 6 Bumpons

Protect your keyboard with the LINE FRIENDS keyboard case.

Specifications

• Outer Dimension - 50 x 24 x 9.5cm (LxWxH)
• Inner Dimension - 44.5 x 17 x 5cm (LxWxD)

Specifications:

• Material : STS420J2
• Hardness : HRC45-48
• Treatment : Black Coating
• Size (single product): 8 mm diameter, 100 mm length
• This product is a precision tolerance product, and only wires within 1.6mm can be used
• 2 pieces per set

Geon x Wolf Fly Daughterboard is a small form factor daughter board made in collaboration between Geon Works and Wolf. Designed as a replacement for the Unified Daughterboard without compromise.

Geon x Wolf Fly Daughter Board Features:

• Molex Pico EZmate Connector
  
• Female Connector Specs: Link
• Male Connector Specs: Link
• ESD chip with integrated bidirectional TVS diode for VBUS
• Common mode filter for D+ and D-
• RC Filter on Shield
• 1A Trip Fuse
• USB-C
• EZmate to EZmate Cable
• 3D File: Link

Includes:

• 1 Geon x Wolf Fly Daughterboard
  
• 1 150mm EZmate to EZmate Cable

TX's new and improved Stabilizer Testers are larger and support more options. They include switch holding brackets to keep the switch in place to perform similar to your keyboard. 

Specs:

• Supports 1x 1U, 2x 3U, 4x 2U, 2x 2.25U, 1x 2.75U, 1x 6U & 1x 6.25U or 7U
• Hotswap sockets to hold the switch in place
• Silicone bumpons

Specifications:

• Material: Aluminum 6063
• Display Angle: 60 degrees
• Weights: 260grams
• Compatibles: TKL, 75%, 65%, 60%, Alice, etcs

Included:

• Black color Silicone Feet, 4pcs
• Gray color Silicone Damper,10pcs
• Flat Head Screw M2.5 x 8, 8pcs

Geon Stabilizer Shim 0.4mm

Features

• Easy to Use: Designed for adhesive application, making it easy to use.
• Two Types Available
• Durable Material: Made from 0.4mm thick flexible plastic, which is less prone to breaking compared to FR-4 material
  

Celebrate the Canadian Mechanical Keyboard Meetup 2025 with the official event T shirt. This custom designed piece was created exclusively for CMK and captures the energy and creativity of the community.

The front features a small chest graphic with the CMK 2025 Fall keycap artwork. The design blends Toronto’s skyline with playful keyboard themed elements and gives the shirt a subtle but standout identity.

The back showcases all supporting vendors and creators who helped make the event possible. Every logo is printed with clarity and arranged in a clean layout that represents the strength of Canada’s mechanical keyboard scene.

Made on a soft, comfortable black tee that fits well for everyday wear or as a collectible reminder of the meetup. Whether you attended in person or are supporting from afar, this shirt is a piece of CMK history made for enthusiasts and friends of the community.

Sizing Chart